Distance-settable Photoelectric Sensors
E3AS-HL Series
E3AS-HL Series CMOS Photoelectric
Sensor for precise part detection
• CMOS photoelectric sensor for advanced part detection
capabilities
• Spot beam and line beam options for small part or uneven
surfaces
• 500mm and 150mm sensing options fit for most sensing
applications
• Antifouling coating prevents contamination
on the sensing surface
• Ecolab certified in addition to IP67/69K/67G protection
• All models with IO-Link connectivity allowing users to
collect and use measurement values
(NPN type excluded)
For the most recent information on models that have been
certified for safety standards, refer to your Omron website.
Refer to Safety Precautions on page 13.
1
E3AS-HL Series
Ordering Information
E3AS-HL models
[Refer to Dimensions on page 15]
Red light
Line beam type
Connection method
Sensing distance
(white paper)
Model
Output
IO-Link baud rate
NPN output
PNP output
---
COM3 (230.4 kbps) 3
E3AS-HL500LMN 2M
E3AS-HL500LMT 2M
M8 Connector
E3AS-HL500LMN M3
E3AS-HL500LMT M3
M12 Pre-wired Smartclick
Connector (0.3m) 2
E3AS-HL500LMN-M1TJ 0.3M
E3AS-HL500LMT-M1TJ 0.3M
E3AS-HL150LMN 2M
E3AS-HL150LMT 2M
M8 Connector
E3AS-HL150LMN M3
E3AS-HL150LMT M3
M12 Pre-wired Smartclick
Connector (0.3m) 2
E3AS-HL150LMN-M1TJ 0.3M
E3AS-HL150LMT-M1TJ 0.3M
Pre-wired (2 m) 1
Pre-wired (2 m) 1
35 mm
35 mm
500 mm
150 mm
Spot type
Connection method
Sensing distance
(white paper)
Model
Output
IO-Link baud rate
NPN output
PNP output
---
COM3 (230.4 kbps) 3
E3AS-HL500MN 2M
E3AS-HL500MT 2M
M8 Connector
E3AS-HL500MN M3
E3AS-HL500MT M3
M12 Pre-wired Smartclick
Connector (0.3m) 2
E3AS-HL500MN-M1TJ 0.3M
E3AS-HL500MT-M1TJ 0.3M
E3AS-HL150MN 2M
E3AS-HL150MT 2M
M8 Connector
E3AS-HL150MN M3
E3AS-HL150MT M3
M12 Pre-wired Smartclick
Connector (0.3m) 2
E3AS-HL150MN-M1TJ 0.3M
E3AS-HL150MT-M1TJ 0.3M
Pre-wired (2 m) 1
Pre-wired (2 m) 1
35 mm
35 mm
500 mm
150 mm
Note: 1. Models with 5-m cable length are also available with “5M” suffix. (Example: E3AS-HL500MN 5M/E3AS-HL500LMN 5M)
2. M8 Pre-wired Connector Models are also availavble. When ordering, add "-M3J 0.3M" to the end of the model number
(e.g., E3AS-HL500MN-M3J 0.3M/E3AS-HL500LMN-M3J 0.3M).
3. COM2 (38.4kbps) Models are also available.
2
E3AS-HL Series
Accessories (Sold Separately)
Sensor I/O Connectors (Sockets on One Cable End)
(Models for Connectors / Pre-wired Connectors)
A Sensor I/O Connector is not provided with the Sensor. It must be ordered separately as required.
Round Water-resistant Connectors XS3F-M8 series
Appearance
Cable specification
Cable diameter
(mm)
Cable connection
direction
M8 Connector
Straight type
Cable length (m)
Sensor I/O Connector
model number
2
XS3F-M8PVC4S2M
5
XS3F-M8PVC4S5M
2
XS3F-M8PVC4A2M
5
XS3F-M8PVC4A5M
Straight
PVC cable
5 dia.
Right-angle type
Right-angle
Note: 1. The XS3W (Socket and Plug on Cable Ends) is also available. Refer to XS3 Series Datasheet (Cat. No. G147).
2. The connectors will not rotate after they are connected.
3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.
Round Water-resistant Connectors XS2 series
Appearance
Cable specification
Cable diameter
(mm)
Cable connection
direction
M12 Connector
Straight type
Cable length (m)
Sensor I/O Connector
model number
2
XS2F-M12PVC4S2M
5
XS2F-M12PVC4S5M
2
XS2F-M12PVC4A2M
5
XS2F-M12PVC4A5M
Straight
PVC robot cable
6 dia.
Right-angle type
Right-angle
Note: 1. The XS2W (Socket and Plug on Cable Ends) is also available. Refer to XS2 on your OMRON website for details.
2. The connectors will not rotate after they are connected.
3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.
3
E3AS-HL Series
Mounting Brackets
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
For E3AS-HL series [Refer to Dimensions on page 16]
Appearance
Model
(material)
Pre-wired
M12 Pre-wired
Smartclick Connector
M8 Connector
E39-L221
(SUS304)
Yes
Yes
---
E39-L222
(SUS304)
Yes
Yes
---
E39-L223
(SUS304)
Yes
Yes
Yes 2
E39-L224
(SUS304)
Yes
Yes
---
E39-L231
(SUS304)
--- 1
--- 1
Yes 3
E39-L232
(SUS304)
--- 1
--- 1
Yes 3
E39-L234
(SUS304)
--- 1
--- 1
Yes 3
E39-E19 4
Yes
Yes
Yes
L-shaped
Mounting Bracket
Horizontal Protective
Cover Bracket
Rear
Mounting Bracket
Robust
Mounting Bracket
L-shaped
Mounting Bracket
Horizontal Protective
Cover Bracket
Robust
Mounting Bracket
Front Protection
Cover
Note: 1.
2.
3.
4.
Can be used for Pre-wired models and M12 Pre-wired Smartclick Connector models. However, confirm the bracket shape in advance.
Confirm the installation environment and bracket shape of the Sensor I/O Connector to be connected.
Use an L-shaped Sensor I/O Connector. Straight types cannot be installed.
Front Protection Cover is Accessory for E3AS-HL. E3AS-F model and E3AS-L model cannot be installed.
4
E3AS-HL Series
E3AS-HL series [Refer to Dimensions on page 19]
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
Appearance
Model
(material)
Pre-wired
M12 Pre-wired
Smartclick Connector
M8 Connector
Yes
Yes
Yes
E39-L262
Yes
Yes
Yes
E39-L263
Yes
Yes
Yes
Yes
Yes
Yes
Flexible
Mounting Bracket
E39-L261
(SUS304)
1
Post 50 mm
Post 100 mm
Air Blow Unit
E39-E16
2
Note: 1. The Flexible Mounting Bracket is not provided with a Post (E39-L262/E39-L263). It must be ordered separately.
2. The tube for air is not included.
5
E3AS-HL Series
Ratings and Specifications
E3AS-HL models
Sensing method
Model
Item
Triangulation
NPN Output
E3AS-HL500MN
E3AS-HL500LMN
E3AS-HL150MN
E3AS-HL150LMN
PNP Output/COM3
E3AS-HL500MT
E3AS-HL500LMT
E3AS-HL150MT
E3AS-HL150LMT
Sensing distance 1
35 mm to the set distance
35 mm to the set distance
Setting range 1
35 to 500 mm
35 to 150 mm
Standard detectable difference 1
35 to 180 mm: 9 mm
180 to 300 mm: 18 mm
300 to 400 mm: 30 mm
400 to 500 mm: 45 mm
at 10 m sec
35 to 50 mm: 1 mm
50 to 100 mm: 2 mm
100 to 150 mm: 4 mm
at 10 m sec
Display minimum unit value
1 mm
Spot size (reference value)
2.5 mm × 1.5 mm
at distance of 500 mm
2
0.1 mm
18 mm × 1.5 mm
at distance of 500 mm
Light source (wavelength)
Red laser (660 nm), Class1 (IEC/EN60825-1:2014)
Power supply voltage
10 to 30 VDC (including 10% ripple (p-p)), Class2
Current consumption
100 mA max.
Control output
Input/
output
2.5 mm × 1.3 mm
at distance of 150 mm
Load power supply voltage 30 VDC max. (Class2), the total load current of the two outputs is 100 mA max.
Residual voltage (Load current 10 mA max.: 1 VDC max., Load current 10 to 100 mA: 2 VDC max.)
Open-collector output (NPN/PNP output depending on model)
N.O. (Normally Open) / N.C. (Normally Close) selectable
NPN
OUTPUT 1: NO (Normally open), OUTPUT 2: NC (Normally closed)
PNP/COM3
OUTPUT 1: NO (Normally open)/COM, OUTPUT 2: NC (Normally closed)
External input
8 mm × 1.3 mm
at distance of 150 mm
Laser OFF / Teaching / Zero reset selectable
NPN ON time: 0 V short-circuit or 1.5 V or less, OFF time: Power supply voltage short-circuit or open
PNP ON time: Power supply voltage short-circuit or within power supply voltage - 1.5 V, OFF time: 0 V short-circuit or open
Response time
1.5 ms / 10 ms / 50 ms selectable
Threshold setting method
Teaching method / Manual Operations / IO-Link communications
Mutual interference prevention
4 units max. (when using the mutual interference prevention function)
Ambient illumination
Receiver surface illuminance:
Incandescent lamp: 20,000 lx max., Sunlight: 25,000 lx max.
at distance of 250 mm
Incandescent lamp: 5,000 lx max., Sunlight: 10,000 lx max.
at distance of 500 mm
Receiver surface illuminance:
Incandescent lamp: 8,000 lx max., Sunlight: 16,000 lx max.
Note: 1. Measured with OMRON's standard workpiece (White ceramic).
2. Defined by D4ó method at the maximum sensing distance. Detection may be influenced if there is light leakage outside the defined region
and the surroundings of the target object have a high reflectance in comparison to the target object. Also, when detecting a workpiece
that is smaller than the spot size, a correct value may not be obtained.
6
E3AS-HL Series
E3AS-HL models
Series
E3AS-HL
Protection circuits
Power supply reverse polarity protection, Output short-circuit protection, and Output reverse
polarity protection
Ambient temperature range
Operating: -10 to 50°C,
Storage: -25 to 70°C
(with no icing or condensation)
Ambient humidity range
Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance
20 M min. at 500 VDC
Dielectric strength
1,000 VAC, 50/60 Hz for 1 min
Vibration resistance
10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection
IP67 (IEC60529) and IP67G 1 (JIS C 0920 Annex 1), IP69K (ISO20653)
Indicators
OLED Display (White), Power/Communication indicator (Green*), Operation indicator
(Orange)
* IO-Link Communication mode: blinking
Connection method
Pre-wired (standard cable length: 2 m), M8 Connector, M12 Pre-wired Smartclick Connector
(standard cable length: 0.3m)
Weight
(packed state/
Sensor only)
Materials
Pre-wired (2 m)
Approx. 180 g/approx. 110 g
M8 Connector
Approx. 120 g/approx. 50 g
M12 Pre-wired Smartclick Connector (0.3m)
Approx. 150 g/approx. 80 g
Case
Stainless steel (SUS316L)
Lens cover and Display
Methacrylic resin (PMMA) (Lens cover: Antifouling coating)
Indicator
Polyamide 11 (PA11)
Operation mode switching between NO and NC, execution of teaching (2-point teaching,
Background teaching), setup of the threshold, timer function of the control output and timer
time selecting, Restore Factory Settings, Key Lock (Unlock, Lock, Lock (No Button)), monitor
output* (Detection level, Incident light level) * Only for E3AS-HL and E3AS-F
Main IO-Link functions
IO-Link Communication
specifications
Accessories
IO-Link specification
Ver. 1.1
Baud rate
COM3 (230.4 kbps)
Data length
PD size: 4 bytes, OD size: 1 byte (M-sequence type: TYPE_2_V)
Minimum cycle time
COM3: 1.2 ms
Instruction manual, compliance sheet, index list (attached for IO-Link type only)
E3AS-HL: FDA certification label and Warning label
E3AS-F: FDA certification label
Note: Mounting Brackets must be ordered separately.
Note: The IP67G is the degree of protection which is defined according to the JIS (Japanese Industrial Standards).
The IP67 indicates the same level of protection as defined by the IEC, and the G indicates that a device has resistance to oil.
7
E3AS-HL Series
Engineering Data (Reference Value)
E3AS-HL models
Line beam type
E3AS-HL500L
E3AS-HL150L
2.5
25
2.5
X
1.5
Y
1
0.5
X
X
20
2
Y
15
Y
1.5
10
1
0.5
5
Spot diameter Y (mm)
2
Spot diameter X (mm)
Spot diameter (mm)
Spot Diameter vs. Sensing Distance
Spot type
E3AS-HL500
E3AS-HL150
X
Y
0
0
0
0
50 100 150 200 250 300 350 400 450 500 550 600
0
50 100 150 200 250 300 350 400 450 500 550 600
Distance (mm)
Distance (mm)
Sensing Object Angle Characteristics
Spot type/Line beam type
E3AS-HL500
Horizontal
Inclination
Angle
Horizontal
Sensing
object
Horizontal
Inclination
Angle
Sensing
object
+θ
+θ
At Sensing distance of 250 mm
Center line
90
80
70
60
50
40
30
20
10
0
White paper
Response time
Black paper 10%
1.5 ms
10 ms
-θ
Horizontal Inclination Angle θ (°)
Horizontal Inclination Angle θ (°)
-θ
At Sensing distance of 500 mm
White paper
SUS
Response time
50 ms
E3AS-HL150
Center line
90
80
70
60
50
40
30
20
10
0
Black paper 10%
1.5 ms
10 ms
SUS
50 ms
Horizontal
Inclination
Angle
Horizontal
Sensing
object
+θ
Horizontal Inclination Angle θ (°)
-θ
At Sensing distance of 150 mm
Center line
90
80
70
60
50
40
30
20
10
0
White paper
Response time
Black paper 10%
1.5 ms
10 ms
SUS
50 ms
8
E3AS-HL Series
30
Minimum Measurement Gap (mm)
Minimum Measurement Gap (mm)
Minimum Measurement Gap Vs. Distance
Spot type/Line beam type
E3AS-HL150
E3AS-HL500
Sensing object:
White paper, Black paper
25
20
15
10
5
1.4
Sensing object:
White paper, Black paper
1.2
1
0.8
0.6
0.4
0.2
0
0
100
200
300
400
500
Sensing distance (mm)
0
0
50
100
150
Sensing distance (mm)
9
E3AS-HL Series
I/O Circuit Diagrams/ Timing Charts
E3AS-HL models
NPN Output
Model
Timing chart
Output circuit
Single Point Mode [Single]
Using Pin2 (white wire) as output
Rated sensing distance range
Threshold
+V
OUT1
OUT2
0V
Power/Communication
indicator (green)
Operation indicator (orange)
Control output 1
Control output 2 *
+V
OUT1
0V
Rated sensing distance range
Near-side
threshold
Operation indicator (orange)
Control output 1
Control output 2 *
Load
White
10 to 30 VDC
Blue
Using Pin2 (white wire) as external input
Window BGS mode [Window BGS]
Power/Communication
indicator (green)
Black Load
Total load current of the two output
routes must be 100 mA or less.
ON
OFF
ON
OFF
ON
OFF
ON
OFF
EXTIN
E3AS-HL500N
E3AS-HL150N
Brown
Far-side
threshold
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Brown
Black
Load 100mA
max.
10 to 30 VDC
White
External Input
Blue
External Input
NPN
ON time
0V short-circuit or 1.5V or less
OFF time
Power supply voltage
short-circuit or open
Connector Pin Arrangement
M12 Pre-wired
Smartclick Connector
M8 Connector
Window FGS mode [Window FGS]
Rated sensing distance range
Near-side
threshold
Power/Communication
indicator (green)
Operation indicator (orange)
Control output 1
Control output 2 *
Far-side
threshold
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Note: The initial value of control output 2 is reverse of control output 1.
10
E3AS-HL Series
PNP Output
Output circuit
Model
Standard I/O mode (SIO mode) 1
IO-Link Communication mode (COM mode) 2
Using Pin2 (white wire) as output
+V
OUT1
OUT2
0V
Using Pin2 (white wire) as output
Brown
Brown
+V
Black
White
Blue Load
100mA
max.
10 to 30 VDC
C/Q
100mA
max.
DO
Load
C/Q
White
IO-Link Master
DI/DO
Blue
0V
Total load current of the two output
routes must be 100 mA or less.
+V
Black
0V
Using Pin2 (white wire) as external input
+V
OUT1
EXTIN
E3AS-HL500T
E3AS-HL150T
0V
Brown
External Input
Black
White
Blue Load
External Input
100mA 10 to 30 VDC
max.
--PNP
ON time
Power supply voltage short-circuit or
within power supply voltage - 1.5V
OFF time
0V short-circuit or open
Connector Pin Arrangement
M12 Pre-wired
Smartclick Connector
M8 Connector
Note: 1. Standard I/O mode is used as PNP ON/OFF output.
2. IO-Link Communication mode is used for communications with the IO-Link Master. C/Q performs IO-Link communications. Sensor output
DO performs ON/OFF output.
Single Point Mode [Single]
Timing charts
Rated sensing distance range
Output mode
Threshold
Power/Communication
indicator (green)
Standard
I/O mode
(SIO mode)
Operation indicator (orange)
Control output 1 2
Control output 2 1, 2
IO-Link
Communication
mode
(COM mode)
11
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Flashing
(1 second cycle)
ON
Operation indicator (orange)
OFF
1
Communication output
0
ON
Control output 2 1, 2
OFF
Power/Communication
indicator (green)
Note: 1. The initial value of control output 2 is reverse
of control output 1.
2. The timer function of the control output can be
set up by the IO-Link communications. (It is
able to select ON delay, OFF delay, or oneshot function and select a timer time of 1 to
9,999 ms (T).)
ON delay
Sensing
object
Present
Not
present
ON
OFF
ON
NC
OFF
NO
1
0
1
0
OFF delay
Sensing
object
T
ON
OFF
ON
NC
OFF
NO
T
Present
Not
present
1
0
1
0
One Shot
Sensing
object
T
ON
OFF
ON
NC
OFF
NO
T
Present
Not
present
T
1
0
1
0
Please contact your OMRON sales representative
regarding the IO-Link setup file (IODD file).
T
E3AS-HL Series
Window BGS mode [Window BGS]
Timing charts
Rated sensing distance range
Output mode
Near-side
threshold
Power/Communication
indicator (green)
Standard
I/O mode
(SIO mode)
Operation indicator (orange)
Control output 1 2
Control output 2 1, 2
IO-Link
Communication
mode
(COM mode)
Far-side
threshold
Note: 1. The initial value of control output 2 is reverse
of control output 1.
2. The timer function of the control output can be
set up by the IO-Link communications. (It is
able to select ON delay, OFF delay, or oneshot function and select a timer time of 1 to
9,999 ms (T).)
ON delay
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Sensing
object
NO
NC
Present
Not
present
ON
OFF delay
Sensing
object
Present
Not
present
T
1
ON
OFF
ON
NC
OFF
NO
OFF 0
ON 1
T
OFF 0
1
0
1
0
One Shot
Sensing
object
T
Present
Not
present
ON
OFF
ON
NC
OFF
NO
T
T
1
0
1
0
T
Please contact your OMRON sales representative
regarding the IO-Link setup file (IODD file).
Flashing
Power/Communication
(1 second cycle)
indicator (green)
ON
Operation indicator (orange)
OFF
1
Communication output
0
ON
Control output 2 1, 2
OFF
Window FGS mode [Window FGS]
Timing charts
Rated sensing distance range
Output mode
Near-side
threshold
Power/Communication
indicator (green)
Standard
I/O mode
(SIO mode)
Operation indicator (orange)
Control output 1 2
Control output 2 1, 2
IO-Link
Communication
mode
(COM mode)
Far-side
threshold
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Flashing
(1 second cycle)
ON
Operation indicator (orange)
OFF
1
Communication output
0
ON
Control output 2 1, 2
OFF
Power/Communication
indicator (green)
Note: 1. The initial value of control output 2 is reverse
of control output 1.
2. The timer function of the control output can be
set up by the IO-Link communications. (It is
able to select ON delay, OFF delay, or oneshot function and select a timer time of 1 to
9,999 ms (T).)
ON delay
Sensing
object
Present
Not
present
ON
OFF
ON
NC
OFF
NO
1
0
1
0
OFF delay
Sensing
object
Present
Not
present
T
ON
OFF
ON
NC
OFF
NO
T
1
0
1
0
One Shot
Sensing
object
T
Present
Not
present
ON
OFF
ON
NC
OFF
NO
T
T
1
0
1
0
T
Please contact your OMRON sales representative
regarding the IO-Link setup file (IODD file).
Note: Shown above are the factory settings. Refer to the index list for the default settings at time of shipment from factory.
PNP/COM output logic can be reversed by IO-Link communication.
The operation indicator (orange) lights up when control output 1 is ON or communication output is 1.
Nomenclature
E3AS-HL500
E3AS-HL150
Operation indicator
(orange)
Threshold value indicator
Displays the set value of
the threshold value in [mm] *.
Teach button
UP button
· Changes the threshold value or set value.
Power/Communication
indicator (green)
DOWN button
· Changes the threshold value or set value.
· To switch between the main screen
and menu setting screen,
press and hold this button for over 3s.
Note: The indicators work differently depending on sensor status.
OUT indicator
Displays output state
of Control output 1
(Pin4, black wire).
OUT indicator
Displays input/output
state of Control output 2
(Pin2, white wire).
Detected value
Displays the current
detected value in [mm] *.
* Reference value
12
E3AS-HL Series
Safety Precautions
Be sure to read the precautions for all models in the website at: http://www.ia.omron.com/.
Warning Indications
E3AS-HL and E3AS-F models
Warning level
Indicates a potentially hazardous situation
which, if not avoided, will result in minor or
moderate injury, or may result in serious
injury or death. Additionally there may be
significant property damage.
WARNING
To safely use laser products
WARNING
Caution level
Do not expose your eyes to the laser beam either
directly or indirectly (i.e., after reflection from a
mirror or shiny surface). The laser beam has a high
power density and exposure may result in loss of
sight.
Precautions for
Safe Use
Supplementary comments on what to do or
avoid doing, to use the product safely.
Do not disassemble this product. Doing so may
cause exposure to the built-in light source which can
damage eyes and skin. Never disassemble it.
Precautions for
Correct Use
Supplementary comments on what to do or
avoid doing, to prevent failure to operate,
malfunction or undesirable effect on
product performance.
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury or in property damage.
CAUTION
Meaning of Product Safety Symbols
General prohibition
Indicates the instructions of unspecified
prohibited action
Caution, fire
Indicates the possibility of fires under specific
conditions.
General caution
Indicates unspecified general alert.
Caution, explosion
Indicates the possibility of explosion under
specific conditions
Laser Caution
Laser safety measures for laser equipment are stipulated by the
country of use. Follow the instructions described below
categorized in four cases.
1. Usage in Japan
The JIS C6802:2014 standard stipulates the safety precautions
that users must take according to the class of the laser
product. This product is classified into class 1 defined by this
standard.
2. Usage in U.S.
This product is subjected to the U.S. FDA (Food and Drug
Administration) laser regulations. This product is classified
into Class 1 by the IEC 60825-1:2014 standard according to the
regulations of Laser Notice No.56 of the FDA standard. This
product is already reported to CDRH (Center for Devices and
Radiological Health).
Accession Number: 1920014-001
When using a device equipped with the product in the U.S.,
attach an FDA certification label near the sensor mounted on
customer equipment.
FDA certification label
Indicates information related to laser safety
Disassembly prohibited
Prohibit the disassembly of a device because
of the possibility of injuries due to electric
shock.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
3. Usage in China
This product is classified into Class 2 by the GB7247.1:2012
(IEC60825-1:2007) standard.
When using a device equipped with the product in China,
attach a Warning label near the sensor mounted on customer
equipment.
Warning label
Do not use it exceeding the rated voltage.
There is a possibility of failure and fire.
CAUTION
Its component may be damaged and/or degree of
protection may be degraded.
Please do not apply high pressure water intensively
at one place during cleaning.
Never use the product with an AC power supply.
Otherwise, explosion may result.
13
4. Usage in countries other than U.S. and China
This product is classified into Class 1 by the IEC/EN 608251:2014 standard.
E3AS-HL Series
Precautions for Safe Use
Precautions for Correct Use
The following precautions must be observed to ensure safe operation.
1. Do not reverse the power supply connection or connect to an AC
current.
2. Do not short the load.
3. Be sure that before making supply the supply voltage is less than
the maximum rated supply voltage (30 VDC).
4. Do not use the product in environments subject to flammable or
explosive gases.
5. Do not use the product under a chemical or an oil environment
without prior evaluation.
6. Do not attempt to modify the product.
7. Do not touch the metal surface with your bare hands when the
temperature is low. Touching the surface may result in a cold burn.
8. Burn injury may occur. The product surface temperature rises
depending on application conditions, such as the ambient
temperature and the power supply voltage. Attention must be paid
during operation or cleaning.
1. Do not hit the product using a hammer for installation.
2. The product must be installed with the specified torque or less.
For M8 connector, the proper tightening torque is from 0.3 to 0.4
Nm. In case of M12 smartclick connector, manually tighten the
connector.
3. Tightening torque for the mounting hole is 0.6 Nm or less (M3
screw).
4. Do not use the product in any atmosphere or environment that
exceeds the ratings.
5. Output pulses may occur when the power supply is turned OFF.
We recommend that you turn OFF the power supply to the load or
load line first.
6. Use an extension cable less than 100 m long for Standard I/O
mode and less than 20 m for IO-Link Communication mode.
7. Do not pull on the cable with excessive strength.
8. Be sure to turn off the power supply when connecting or
disconnecting the cable.
9. Please wait for at least 600 ms (E3AS-HL), 500 ms (E3AS-F), 100
ms (E3AS-L) after turning on the product's power until it is
available for use.
10.Though this is type IP67, do not use in the water, rain or outdoors.
11.If the Sensor wiring is placed in the same conduits or ducts as
high-voltage or high-power lines, inductive noise may cause
malfunction or damage. Wire the cables separately or use a
shielded cable.
12.Do not use the product in locations subject to direct sunlight.
13.Do not use the product where humidity is high and dew
condensation may occur.
14.Do not use the product where corrosive gases may exist.
15.If high-pressure washing water and so on hits the button, it might
lead to malfunctioning. So, consider use of the key lock function.
16.Do not apply high-pressure washing water directly to the sensor's
light emitting / receiving surface from a short distance. As the
antifouling feature may be impaired, keep a sufficient distance
from the light emitting / receiving surface.
17.Do not use the product at a location subject to shock or vibration.
18.To use a commercially available switching regulator, FG (frame
ground) must be grounded.
19.Do not use organic solvents (e.g. paint thinner and alcohol) for
cleaning. Otherwise optical properties and protective structure
may deteriorate.
20.Be sure to check the influence caused by surrounding
environments such as background objects and LED lighting before
using the product.
21.Do not exceed 100,000 writing operations of the EEPROM (nonvolatile memory). Setting information is written to the EEPROM
when a threshold value change, teaching, or zero reset is
executed.
22.
Please dispose in accordance with applicable regulations.
14
E3AS-HL Series
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise
specified.
Sensors
Pre-wired Models/Pre-wired Connector Models
E3AS-HL500 (-M1TJ)
E3AS-HL150 (-M1TJ)
Operation indicator (orange)
Teach button
16
UP button
9.2
Pre-wired Connector Models
E3AS-HL500-M1TJ
E3AS-HL150-M1TJ
7.5
15.5
6
4.25 dia. vinyl-insulated
round cable with 4 conductors.
DOWN button
2
1
3
4
Power/Communication indicator
(green)
M12×P1
30.4
Two, M3
Reception canter
(Lens: 8 dia.)
6.35
5
28.7
3
1.6
7.7
Minimum bending radius/unbendable
length of cord
(15.4)
Unbendable length
5 mm
47 25.4
11.5
Emission center
(Lens: 3 dia.)
Minimum bending radius
R13 mm
12.4
4.25 dia. vinyl-insulated
round cable with 4conductors
(Conductor cross section:0.3 mm2,
Insulator diameter: 1.05 mm),
Standard length: 2 m
Connector Models
Operation indicator (orange)
E3AS-HL500 M3
E3AS-HL150 M3
Teach button
16
UP button
9.2
7.5
15.5
6
DOWN button
Power/Communication indicator
(green)
Two, M3
Reception canter
(Lens: 8 dia.)
6.35
28.9
3
1.6
7.7
(15.4)
45.5
11.5
25.4
52.5
Emission center
(Lens: 3 dia.)
M8x1
7.5
15
15.75
5
E3AS-HL Series
Accessories (Sold Separately)
Mounting Brackets
For E3AS-HL models
E39-L221
14.5
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
(Six, R2.3)
4.5
15.5
2.5
28.7
4.5
29
17.5
4.5
3
5 7.5
24.5
Four, 3.5
*
Receiver lens
8 dia.
Two, R25.4
(Eight, R1.8)
11.5
58.2
Emitter lens
3 dia.
6.2
30.2
24
25
(T3)
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
9.2
39
23.7
E39-L222
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
16.5
20.5
40.5
32.5
22
26.5
12.2
135°
7
8.5
Receiver lens
8 dia.
*
Four, 3.5 dia.
25.4
11.5
62.2
90.2
Emitter lens
3 dia.
4.5 dia.
6.2
46.5
40.3
4.5
25
14°
10.5
4.5
(T3)
4
R25
11.5
23.5
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
E39-L223
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
24
13.5
(T3)
46.7
4.5
12.2
42
12
53
*
Receiver lens
8 dia.
12.3
37
36
53
19.2
11.5
R25.4
12
3.5
4.5
(Four, R2.3)
22.5
(Four, R2.3)
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
Emitter lens
3 dia.
20°
54
16
E3AS-HL Series
E39-L224
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
(Four, R2.3)
43.5 dia.
Two, 4.5
36
50°
58 dia.
34.5
12.2
27.5
17.5
7
135°
1.4
Two, 3.5
9
*
Receiver lens
8 dia.
Two, R25.4
11.5
(Four, R1.8)
60.1
54.1
Emitter lens
3 dia.
6.2 30.2
24
(T3)
6.6
Two, 5°
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
E39-L231
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
14.5
15.5
(Six, R2.3)
4.5
2.5
4.5
28.7
29
17.5
4.5
7.5
5
24.5
Four, 3.5
Two, R25.4
3
Receiver lens
8 dia.
*
(Eight, R1.8)
11.5
Emitter lens
3 dia.
79.2
6.2
51.2
45
25
(T3)
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
17
39
9.2
23.7
E3AS-HL Series
E39-L232
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
16.5
20.5
40.5
32.5
22
12.2
26.5
135°
Receiver lens
8 dia.
8.5
7
Four, 3.5 dia.
*
25.4
11.5
6.2
Emitter lens
3 dia.
79
107
63.3
57.1
4.5 dia.
4.5
25
14°
10.5
4.5
(T3)
4
R25
(Four, R2.3)
11.5
23.5
22.5
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
E39-L234
43.5 dia.
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
(Four, R2.3)
Two, 4.5
36
50°
58 dia.
34.5
27.5
17.5
7
12.2
135°
1.4
2-3.5
9
Two, R25.4
Receiver lens
8 dia.
(Four, R1.8)
11.5
81.1
75.1
Emitter lens
3 dia.
6.2
51.2
45
(T3)
*
6.6
Two, 5°
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
18
E3AS-HL Series
Common to E3AS series
Flexible Mounting Bracket
E39-L261
Accessories
M5 Hexagon Nut
Material: Stainless (SUSXM7)
17.3
25
23 13
3.2
Accessories
M5-L15 Hexagon Socket
Head Cap Screws
Material: Stainless (SUSXM7)
20 dia.
22 dia.
12 dia.
20 dia, 24 dia.
Two, 3.5 dia.
8.7 dia.
25.4
16 18.5 23
37.6
3.3
4.3
Material: ZDC2
Finished: NI Plaiting
12
17
5
31
Material: Stainless steel (SUS304)
12
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
14 15.1
15 17
12 dia.
E3AS-HL500
*
Receiver lens 8 dia.
22.1
5
6.5
25.4
48.7 47.2
26.6
Emitter lens 3 dia.
60 (E39-L262)
110 (E39-L263)
E39-L262
E39-L263
32
M12xP1.75
18
24.4
33.5
12
25
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
12
8.4
6
14
15 17
12 dia.
E3AS-F1500
*
Receiver lens 2 dia.
18.8
1.5
1.6
25.4
41 39.4
22.1
Emitter lens 3 dia.
60 (E39-L262)
110 (E39-L263)
E39-L262
E39-L263
32
M12xP1.75
12
* Accessories 2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS)
19
25
18
23.7
29.4
12
E3AS-HL Series
Post 50 mm
E39-L262
Accessories
2-M12 Hexagon Nut
Material: Stainless (SUSXM7)
M12x1.8-6g
32
12 dia.
Accessories
2-M12 Plain Washer
Material: Stainless (SUS304)
60
Material: Stainless steel (SUS304)
Post 100 mm
E39-L263
Accessories
2-M12 Hexagon Nut
Material: Stainless (SUSXM7)
M12x1.8-6g
32
12 dia.
110
Accessories
2-M12 Plain Washer
Material: Stainless (SUS304)
Material: Stainless steel (SUS304)
20
E3AS-HL Series
E39-E19
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
15.1
2.7
83°
2.4
T0.5
83°
13.7
4.4
16
(18.9)
34.6
15.9
10.7
(Four, R1.6)
Cover
12
4.3
3.2
32
33.1
*
25.4
20.5
34 25.4
3.2
4.3
6.5
2
Material: Stainless steel (SUS304)
* Accessories
2-M3-L10 Cross Recessed Pan Head Screws (Attached to SW+JIS W)
21
Cover lens
Material: PC
E3AS-HL Series
Air Blow Unit
E39-E16
Accessories
Fitting Air (SMC:KQ2H06-M5N1)
Material: Brass
Finished: NI Plating
6 10
Air Supply Port
M5x0.8-6H
5
Air Blow Outlet Holes
5-2 dia.
25.4
40
4xP5=20
29
11
2- 3.3 PENETRATION
3.3 dia.
9.5
4.5
Accessories
M5-L8 Cross Recessed Pan Head
Screws (Attached to SW+JIS)
Material: Stainless (SUSXM7)
Air Supply Port
10
14
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
15.5
26.5
35.7
7
2
*
40
25.4
5.1
Photoelectric Sensor
Accessory are installed
(Example of E3AS-HL500)
11.4
22.4
7
29
1.25
*
40
25.4
0.65
Material: ZDC2
Finished: NI Plaiting
* Accessories 2-M3-L16 Cross Recessed Pan Head Screws (Attached to SW+JIS)
22
E3AS-HL Series
•
•
•
•
•
•
23
EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.
EtherNet/IP™ is a trademark of ODVA.
Ecolab and its logo are registered trademarks of Ecolab USA Inc.
Smartclick is a registered trademark of OMRON Corporation.
Other company names and product names in this document are the trademarks or registered trademarks of their respective companies.
The product photographs and figures that are used in this catalog may vary somewhat from the actual products.
OMRON AUTOMATION AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • automation.omron.com
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • automation.omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55 11 5171-8920 • automation.omron.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
Ciudad de México • 52.55.5901.4300 • 01.800.386.6766 • mela@omron.com
OMRON ARGENTINA • SALES OFFICE
Buenos Aires, Argentina • +54.11.4521.8630 • +54.11.4523.8483
mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
San Pedro Garza García, N.L. • 81.12.53.7392 • 01.800.386.6766 • mela@omron.
com
OTHER OMRON LATIN AMERICA SALES
+54.11.4521.8630 • +54.11.4523.8483 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Eugenio Garza Sada,León, Gto • 01.800.386.6766 • mela@omron.com
Controllers & I/O
• Machine Automation Controllers (MAC) • Motion Controllers
• Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O
Authorized Distributor:
Robotics
• Industrial Robots • Mobile Robots
Operator Interfaces
• Human Machine Interface (HMI)
Motion & Drives
• Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems
• Frequency Inverters
Vision, Measurement & Identification
• Vision Sensors & Systems • Measurement Sensors • Auto Identification
Systems
Sensing
• Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors
• Rotary Encoders • Ultrasonic Sensors
Safety
• Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems
• Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices
• Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays
Control Components
• Power Supplies • Timers • Counters • Programmable Relays
• Digital Panel Meters • Monitoring Products
Switches & Relays
• Limit Switches • Pushbutton Switches • Electromechanical Relays
• Solid State Relays
Software
• Programming & Configuration • Runtime
E60I-E-01
Note: Specifications are subject to change.
© 2020 Omron. All Rights Reserved.
Printed on recycled paper.
Printed in U.S.A.
